There will be a plastic sleeve covering two of the pins, if not then check the hard drive packaging to locate it. This black sleeve is what you will use to configure your device as one of the options below.
In fig 1. There are 3 connectors, notice the difference in distance between the connectors. Connection A plugs into the motherboard and then the slave and master connections are used for IDE devices. If you are only installing one drive or the new drive is to be the master then use the master connector.
If the drive is to be the slave then use the slave connector. The IDE cable will be marked down one side with a red or black strip, this denotes Pin 1, match this with the pin 1 indicator on the back of the hard drive see fig 1. The power cable can be found attached to your computer case's power supply. Carefully but firmly plug the IDE and power cables in and then move onto finishing the installation below. SATA data cables, labelled A in our diagram are standard and will only insert one-way.
This involves powering your computer on, and clicking a few buttons in software. Have you replaced or installed a SATA hard drive before? If you found this guide helpful, or have any questions, feel free to drop us a comment below.
Save my name, email, and website in this browser for the next time I comment. I accept the Privacy Policy. This website uses cookies so that we can provide you with the best user experience possible.
Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful. Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings. If you disable this cookie, we will not be able to save your preferences.
This means that every time you visit this website you will need to enable or disable cookies again. The magnetic tip is a huge help for holding screws while you work. Job Preparation When working with computers, always consider safety first.
Again, you can skip this check if you are simply replacing your existing hard drive Installing a New Hard Drive Step 1 : Open Up Your Computer Case Turn off your computer and and unplug it from mains power before you begin. Slide off the side cover of your computer and put the side panel aside. The two different types together look like this: These are the two options for connecting power to your hard drive.
You only need to connect one or the other. Secure the drive into the drive bay by inserting two screws into each side of the hard drive through the corresponding holes in the drive bay. Make sure to only use short screws designed for hard drives; if the screws are too long they could seriously damage the hard drive when it is running.
Connect the SATA cables to the hard drive. Connect the insulated power cable with the wider tip into the larger connection port situated on the left-rear of the HDD. If the power cable does not fit easily, check to make sure that it is not upside down.
Connect the data cable to the smaller SATA port on the hard drive. If the power supply is older, it may not have any SATA power connectors. Molex plugs have four pins, and may be white or black. Connect the data cable to the motherboard. If you are adding a new drive, you will need to connect the data cable to a SATA port on the motherboard if you are replacing and old drive, the data cable should already be connected.
SATA ports are usually grouped together and labeled. Your primary boot drive should be connected to the lowest SATA port on your motherboard, unless otherwise specified in your motherboard documentation. You will need to install a motherboard that supports the SATA format. Finish the installation. Once the hard drive is secured and connected, close up your computer and power it back on. Before you can use your new drive, you will need to format it. If you are replacing the primary drive or building a new computer, you will need to install your operating system.
Follow one of the guides below for more detailed instructions: Install Windows 7. Install Windows 8. Install Linux. Format your new storage drive. Method 2. Turn off the power switch on the back of the power supply, but leave the cable plugged in if possible. This will help keep you grounded. If you have to unplug everything, be sure to follow Step 2 closely.
Open the case using the thumbscrews or a screwdriver if necessary. You will need to remove both side panels on many older cases and some newer ones in order to properly secure the drive. Insert your new optical drive. Most optical drives are inserted from the front of the case. Secure the drive using two screws on each side, or by using rails if your case has them.
Connect the power supply to the optical drive. If your power supply is older, it may only have Molex 4-pin connectors. Connect the optical drive to the motherboard. Use the smaller SATA data cable to connect the optical drive to the motherboard.
Use the SATA port on the motherboard directly after your last hard drive. You will need to install a new motherboard if you want to use your SATA drive. Once the optical drive is secured and connected, you can close up your computer and power it back on. Your new drive should be automatically detected, and any necessary drivers will be installed automatically.
Method 3. Back up your data. Most laptops only have one hard drive slot, so if you replace your hard drive you will lose access to all of your old data. Ensure that anything you need is properly backed up , and that you have your operating system installation discs handy to install the operating system after the new drive is installed.
Power down the laptop. Turn it over and remove the battery. Make sure that the power cable is not plugged it. Ground yourself, either by wearing an antistatic wrist strap, or by touching grounded metal.
0コメント